The free newsletter of Lean Manufacturing Strategy
Lean Briefing Archives
Books & Videos
The Strategos Guide To Value Stream and Process Mapping goes far beyond symbols and arrows. In over 163 pages it tells the reader not only how to do it but what to do with it.
More info...
Strategos Guide to Value Stream & Process Mapping
Also...
Guide to Cycle Counting
Facilities & Workplace Design
Warehouse Planning Guide
Human Side of Lean Video
|
|
A Bomber An Hour
Lean Manufacturing circa 1944
|
Production Miracle At Willow Run
In January of 1940, America was being drawn into the growing war and our military was
woefully unprepared. The Roosevelt administration asked Ford Motor Company to manufacture
components for the B-24 Liberator bomber.
Charles Sorensen, Vice-President of Production for
Ford traveled to San Diego to observe Consolidated Aircraft's operations. Here is his
description of the visit and how he conceived the Willow Run bomber plant that eventually
manufactured 8,800 of these aircraft.
Willow Run was the physical embodiment of the Ford Production system which was later
transformed by Toyota into "Just In Time" and
Lean manufacturing. This is where it all started.
|
The narrative below is Sorensen's own account of the birth of Willow Run as told in "My Forty
Years With Ford."
References
SORENSEN, CHARLES E., My Forty Years With Ford. New York: W.W. Norton, 1956.
LACEY, ROBERT, Ford: The Men and The Machine, Boston, MA, Little Brown, 1986.
KIDDER, WARREN BENJAMIN, Willow Run: Colossus of American Industry, Lansing, MI, KFT, 1995.
This article is available free in printer-friendly pdf format.
|
|
Willow Run became a reality. It was the embodiment of
American ingenuity, perseverance and productivity. Here are some of the statistics:
-
488,193 parts
-
30,000 components
-
24 Major subassemblies
-
Peak production- 25 units per day
-
25,000 initial engineering drawings
-
Ten model changes in six years
-
Thousands of running changes
-
34,533 employees at peak
-
100% Productivity improvement
|
|
Charlie Sorensen's Story
Inside the (Consolidated) plant I watched men putting together wing sections and portions of
the fuselage. The work of putting together a four-engine bomber was many times more complicated
than assembling a four-cylinder automobile, but what I saw reminded me of nearly thirty-five
years previously when we were making Model N Fords at the
Piquette Avenue plant. This was
before Walter Flanders rearranged our machines and eight years before we achieved the orderly
sequence of the assembly line and mass production.
The nearer a B-24 came to its final assembly the fewer principles of mass production there
were as we at Ford had developed and applied over the years. Here was a custom-made plane, put
together as a tailor would cut and fit a suit of clothes.
|
The B-24's final assembly was made out of doors under the bright California sun and on a
structural steel fixture. The heat and temperature changes so distorted this fixture that it was
impossible to turn out two planes alike without further adjustment. The Consolidated and the Air
Force people talked about an order from Ford Motor Company for center and outer wing sections;
but it was obvious that if the wing sections had uniform measurements, the way we made parts for
automobiles, they would not fit properly under out-of-doors assembly conditions.
All this was pretty discouraging, and I said so. Naturally, and quite properly, the reply was
"How would you do it?" I had to put up or shut up. "I'll have something for you tomorrow morning," I said.
|
Charles E. Sorensen
|
|
Riveting Lower Wing Skin
|
|
Machinist At Willow Run
|
|
I really did have something in mind. To compare a Ford V-8 with a four-engine Liberator
bomber was like matching a garage with a skyscraper, but despite their great differences I knew
the same fundamentals applied to high-volume production of both, the same as they would to an
electric egg beater or to a wrist watch.
First, break the plane's design into essential units and make a separate production layout
for each unit. Next, build as many units as are required, then deliver each unit in its proper
sequence to the assembly line to make one whole unit~ finished plane.
To house all this and provide for efficient operation there should be a new plant specially
designed to accommodate the progressive layout. I saw no impossibility in such an idea even
though mass production of anything approaching the size and complexity of a B-24 never had been
attempted before.
But who would accept such a wild notion? And instead of one bomber a day by the prevailing
method I saw the possibility of one B-24 an hour by mass production assembly lines. How could
the aviation people take that estimate seriously?
As soon as I returned to my room at the Coronado Hotel, I began figuring how to adapt Ford
assembly methods to airplane construction and turn out one four-engine bomber an hour.
Throughout the day I had made copious notes. I listed all major units of the plane and the
subunits and fractional units required for their assembly, and I had gathered figures on
Consolidated's labor force and job performance.
From these I computed each unit operation, its timing, and required floor space as I saw
them, and paper began to fly. Figures for each unit I kept together in a separate pile, and soon
there were little stacks of paper all over the floor of my room.
I was back at my old game of sketching a series of manufacturing and subassembly operations
and their orderly progression toward becoming major units-- a game I had played many times since
that morning in 1908 at the Piquette Avenue plant when we first experimented with a moving
assembly line.
Now, in one night, I was applying thirty-five years of production experience to planning the
layout for building not only something I had never put together before, but the largest and most
complicated of all air transport and in numbers and at a rate never before thought possible.
Again I was practicing my production planning philosophy, which stemmed from my patternmaking
days when I fashioned wooden models of Henry Ford's half-thought-out designs: "Unless you see a
thing, you cannot simplify it. And unless you can simplify it, it's a good sign you can't make
it.?
|
Wing Assembly
Two parallel assembly lines converge after the
outer wing is attached.
|
As I look back now upon that night, this was the biggest challenge of my production
career-bigger than any Model T assembly line sequence for
Highland Park, more momentous than
the layout and construction of the great River Rouge plant in which I'd had a part. It took
eight years to develop Ford's mass production system, and eight more years before we worked up
to a production of 10,000 cars a day.
Once again I was going on the principle I had enunciated many times at Ford: "The only thing
we can't make is something we can't think about."
Through most of the night I set down figures and revised them. I arranged and rearranged the
stacks of paper, as it became plainer to me which unit came after the other in moving to final
assembly and how much floor space was involved.
Landing Gear Inspection
|
At length the whole picture became clear and simple. I knew I had the solution, and I was
elated by the certainty that the Germans had neither the facilities nor the conception for
greater bomber mass production.
Towards four o'clock, I was satisfied that my piles of paper were arranged in proper order
and represented the most logical progress of units to the main assembly line; and I knew I could
prove a construction rate of one big bomber an hour. Now I had something to talk about.
|
Charles Sorensen's Original Sketches
|
Standing over the papers, I roughed out on Coronado Hotel notepaper a pencil sketch of the
floor plan of a bomber plant. It would be a mile long and a quarter mile wide, the biggest
single industrial building ever. I still have that sketch, initialed by
Edsel Ford, his two sons and others, and I
still get a kick out of it.
The result of one night's hard work, it is the true outline of Willow Run, which took two
years to build and came through on schedule with one four-engine Liberator an hour, 18 bombers a
day, and by the end of the war a total of 8,800 big planes off the assembly lines and into the
air.
When I finished my sketch I went to bed, but was so carried away by enthusiasm for the
project that I couldn't sleep. I was building planes the rest of the night.
|
B-24 Test Flight Over Michigan |
At breakfast with Edsel (Ford) the next
morning I was somewhat woozy as I showed him the sketch and outlined the bomber-an-hour proposition.
He was in complete accord and assured me that Ford
Motor Company would build such a plant. My high respect for him went higher than ever. We spent
an hour together, getting set for a meeting in Major Fleet's office to shoot the works on a $200,000,000 proposition backed only by a penciled sketch.
|
Willow Run Bomber Plant
Albert Kahn, a prominent industrial architect translated Sorensens sketches into bricks
and mortar. The final design was L-shaped because of some problems with easements for
adjacent property. Willow Run Airport is in the background.
|
|
Willow Run Plant Layout circa 1944
Click To Enlarge
|
|
|
|